Please select To the mobile version | Continue to access the desktop computer version

zeusbtc bbs

 Forgot password?
 Sign up now
Search
12Next
Return to list New
View: 374|Reply: 10

Precautions for the Innosilicon Mining Farm

[Copy link]

65

Threads

65

Posts

246

Credits

Moderator

Rank: 7Rank: 7Rank: 7

Credits
246
Post time 2021-11-20 10:10:22 | Show all posts |Read mode
Precautions for the Innosilicon mining farm
The digital coin miner is a high-end computing server, and the mining farm is a data center. Therefore, a ventilated, dust-proof, and reliable environment is required to ensure the maximum hash rate, lowest failure rate, and most extended service life. Only in an excellent operating environment can we obtain a high hash rate and returns.
Keep a good data center, must attention be paid to temperature, humidity, dust prevention, and stable power supply. In addition, the miner should be put on and off the shelf correctly. At the same time, do an excellent job of cold and heat isolation and daily inspections.
I. Temperature requirements
Operating temperature: 0-40℃
However, the actual humidity, dust, etc., will narrow the temperature range. Therefore, it is recommended to keep the mine site temperature between 5°C and 35°C, with 25°C being the best temperature.
Storage temperature: -20℃-70℃
II. Humidity requirements
Relative operating humidity: 10-90%, no condensation
Relative storage humidity: 5-95%, no condensation
III. Dustproof requirements
1. The equipment room needs to be far from industrial pollution sources, oceans, or salt lakes, without explosive, conductive (such as metal dust lamps), magnetic and corrosive (such as sulfide, chlorine, and ammonia) dust or gas.
2. When there is sand or dust in the equipment room, it is necessary to install a dustproof net and regularly use a vacuum cleaner to vacuum the dust.
IV. Set up the miner correctly
1. Before setting up the miner, please check whether there is a violent bumping prompt, whether the heat sink falls off due to shaking, and whether the fan is damaged in appearance.
2. Check whether the wiring (fan and hash board) and the power cable are properly connected to avoid looseness.
3. The miner should be powered off before installation, and handle it gently when off the shelf. It is forbidden to place and drop randomly and to carry the hash board wiring by hand.
V. Remove the miner off the shelf properly
1. Reconfirm whether the fault can be repaired on-site before taking it off the shelf.
2. Check whether the IP corresponds to the miner to avoid a mismatch. You can reconfirm it by lighting the red light or reporting IP by the bulk management tool.
3. If the data center has cold and heat isolation, block the air outlet where the miner is located to avoid the return of hot air while removing the miner.
4. The off-shelf miner should be dust-proof, moisture-proof, and placed in a stable and orderly manner.
VI. Keep the power supply stable
1. The miner socket voltage is stable within the normal range of 220V±10%. However, if the voltage is too high or too low, it may cause unstable operation and burn the power supply.
2. The three-phase current deviation of the power distribution cabinet shall not exceed 15%. Otherwise, an electrician should be notified to check whether the three-phase load is balanced. This imbalance may cause the voltage of a particular phase to rise.
3. Check whether the factory shelves and miners are regularly grounded (requires grounding resistance to be less than 4Ω). If there is no grounding or the grounding is good, please notify a professional electrician to complete the grounding work in time. Also, if you often feel a tingling sensation during the operation and maintenance of the miner, please check whether the grounding work is done well or not. You can also choose to buy a leakage protector to ensure that the primary circuit will not be burned out when the leakage occurs.
4. The cable cannot be placed in the hot air area. Please check the aging of the cable regularly.
5. Try to avoid frequent power outages in the mining farm. Planned outages are necessary. If you need to cut off the power, please turn off the automatic air switch on the shelf in ascending order of power, and finally turn off the main switch. Before powering on, make sure that all air switches connected to the miner on the rack are turned off. The air switch should be opened in descending order from the main switch to avoid possible damage caused by transient voltage surges.
VII. Isolate cold and heat well
Mines must be well insulated from heat and cold, especially high-power miners.
Precautions for heat and cold isolation:
VIII. Daily inspection of operation and maintenance
Check the miner's temperature, humidity, appearance, environmental conditions, power supply status, etc., on the miner and the mining farm. Please refer to the attached table for detailed inspection items.
Doing the contents listed above to provide an excellent operating environment for your high-end server is a robust measure to ensure your miner's high hash rate and high return.

ASIC Miner Repair Toturials and Guides
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:30:27 | Show all posts
Your blog provided us with valuable information to work with. Each & every tips of your post are awesome. Thanks a lot for sharing. Keep blogging,        CodeSmith
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:31:34 | Show all posts
Very awesome!!! When I seek for this I found this website at the top of all blogs in search engine.        Lurralife
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:37:49 | Show all posts
Thanks for the nice blog. It was very useful for me. I'm happy I found this blog. Thank you for sharing with us,I too always learn something new from your post.        CodeSmith
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:38:07 | Show all posts
You completely match our expectation and the variety of our information.        Lurralife
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:41:22 | Show all posts
I like viewing web sites which comprehend the price of delivering the excellent useful resource free of charge. I truly adored reading your posting. Thank you!        CodeSmith
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:43:42 | Show all posts
I am looking for and I love to post a comment that "The content of your post is awesome" Great work!        Jason and James
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:43:59 | Show all posts
The blog and data is excellent and informative as well        Elepreneurs
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:47:25 | Show all posts
If you don"t mind proceed with this extraordinary work and I anticipate a greater amount of your magnificent blog entries        Elepreneurs
Reply

Use magic Report

3

Threads

652

Posts

1403

Credits

Gold member

Rank: 6Rank: 6

Credits
1403
Post time 2022-8-28 23:51:22 | Show all posts
It’s very informative and you are obviously very knowledgeable in this area. You have opened my eyes to varying views on this topic with interesting and solid content.        Jason and James
Reply

Use magic Report

12Next
Return to list New
You have to log in before you can reply Login | Sign up now

Points Rules

Privacy Policy Terms of Service
Quick Reply To Top Return to the list